The Foundation of Plumbing Knowledge When Installing a Bathtub
The Foundation of Plumbing Knowledge When Installing a Bathtub
Blog Article
We have stumbled upon the article involving A Step-by-Step Guide to Installing a Bathtub below on the net and reckoned it made sense to discuss it with you on this page.
Setting up a bathtub isn't precisely rocket science, but it does require strong plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old tub with a brand-new one is also a moderately challenging task. If the old bathtub is conveniently accessible, the task can move immediately; if you need to open a wall surface to eliminate the old tub and also position the new tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will certainly need an assistant to move out the old tub and also set in the brand-new one. Ensure you have actually certified on your own for the job as well as fit trying it. As opposed to hiring a service provider to take over a halfway-completed task, it is far better to consider using one before you begin. Opportunities are you may need an expert plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your bathroom if you have currently bought a new bathtub and also do not need to change the arrangement of your previous water supply pipelines.
Your devices and also product checklist should consist of the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning throughout this process. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in location in between the faucet as well as the sink. Safeguard the tap in position with the manufacturer given backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet connectors. The former type must be attached to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Making use of both wood boards under its feet, position the tub in the needed setting. The wood boards are valuable in equally spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the bath tub until the spirit level reads level.
To install taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Turn on the water and also inspect all joints as well as brand-new pipework for leakages and tighten them if necessary. Fill the bath tub and also examine the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, deal with the bath paneling as described in the supplier's user's manual. Tiling and also securing around the tub must wait till the bath tub has been made use of at least when as this will certainly settle it right into its last position.
Getting ready for the Setup
To start with, the supporting structure provided with the bathroom needs to be fitted (if needed) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the tap features a plastic washer, it is fitted in between the bath and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets device to prevent stress on the bath tub.
Fit the adaptable tap adapters to the bottom of the two faucets making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you use every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last position.
Tiling Around the Bath tub
In the area where the bath satisfies the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split an inflexible seal, creating the water to pass through the wall between the bath and the tiling, causing difficulties with wetness as well as possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes as well as cartridges, and can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealant can split relatively early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly offered on the market. It is suggested to fit the floor tiles using waterproof or waterproof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate reader on How to Install a Bathtub Yourself, I think sharing that post was sensible. Do you know anybody else who is involved in How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Be sure share it. Thanks a bunch for your time. Please check our blog back soon.
Article Report this page